Name coin bankحصّالة بالاسم

A coin bank shaped like your nameحصّالة على شكل اسمك

Type a name and it becomes a money box. Closed on top with a coin slot; the whole front face is a separate piece that snaps on tight — pull it off to get the coins out. Prints as 2 files (body + face).اكتب اسماً ليصبح حصّالة نقود. مقفولة من فوق وبها شق للعملة؛ الوش الأمامي كله قطعة منفصلة تتركّب بإحكام — اسحبها لتُخرج الفلوس. تُطبع كملفين (جسم + وش).

Building…جارٍ البناء…
Short names work best. Arabic is supported.الأسماء القصيرة أفضل. العربية مدعومة.
Overall height of the print. Minimum 70 mm.ارتفاع القطعة الكلي. الحد الأدنى 70 مم.
Spreads the letters apart (or pulls them tighter). Latin only — Arabic stays joined.يباعد الحروف أو يقاربها. للحروف اللاتينية فقط — تبقى العربية متصلة.
How thick the bank is (front to back). Bigger holds more coins.سماكة الحصّالة (من الأمام للخلف). الأكبر يسع فلوس أكثر.
Closes gaps between letters (and inside a letter) so there are no see-through holes.يسدّ الفراغات بين الحروف وداخل الحرف حتى لا تظهر فتحات نافذة.

Coin slot & faceشق العملة والوش

The slot on top that coins drop through. ~2.6 mm suits most coins; widen for thick ones.الشق اللي فوق اللي بتنزل منه العملة. ٢٫٦ مم يناسب معظم العملات؛ وسّعه للعملات السميكة.
Slide the coin slot along the top — put it over a letter for the cleanest look. It cuts straight down into the hollow.حرّك شق العملة على طول القمة — حطّه فوق حرف عشان أنضف شكل. بيقص لتحت مباشرة في الفراغ.
Gap between the face plug and the body. Smaller = harder to pull off (coins stay in). 0.10–0.15 mm is a firm snap.الخلوص بين لسان الوش والجسم. الأصغر = أصعب في الفتح (الفلوس تفضل جوّه). ٠٫١٠–٠٫١٥ مم تركيب محكم.
How deep the face plugs into the body. Deeper = grips harder and won't fall off.عمق دخول الوش جوّه الجسم. الأعمق = مسك أقوى ومش هيقع.
By default the name is FLUSH with the face and prints in the 2nd colour (same surface). Raise it above 0 to make the letters stand proud; width = how bold/thick the letters are.افتراضيًا الاسم بمستوى الوش نفسه ويُطبع باللون الثاني (نفس السطح). ارفع القيمة فوق الصفر لتبرز الحروف؛ العرض = سماكة/غِلظ الحروف.
A flat base helps it stand and print without supports.قاعدة مسطّحة تساعدها على الوقوف والطباعة بدون دعامات.

Colors (preview)الألوان (معاينة)

The name prints in the second colour on the SAME face piece — each colour is its own part (assign a filament in the slicer), no gluing. One 3MF, two beds: body + face.الاسم يُطبع باللون الثاني على نفس قطعة الوش — كل لون قطعة مستقلة (اختر خيطًا في السلايسر)، بدون لصق. ملف 3MF واحد، سطحان: جسم + وش.